Dovecot CE
2.3
main

Appearance

Edit this page

Updated:

Revision: 055ad6a

Note: This is pre-release documentation.
Please access https://doc.dovecot.org/latest/ for documentation on released versions.

Doveadm Protocol ​

TIP

See also:

doveadm-server can be accessed via UNIX sockets or TCP protocol (by adding inet_listener to doveadm service).

The doveadm server supports the following protocol versions (major.minor):

  • 1.0: Supported since Dovecot v2.0.0.
  • 1.1: Supported since Dovecot v2.2.33. Using this minor number changes the protocol to use multiplex-stream for proxying logs.
  • 1.2: Supported since Dovecot v2.3.9. Indicates that the server supports the STARTTLS command.

For external doveadm clients it's easiest to just support the 1.0 version.

Protocol Overview ​

Initial handshake from client to server:

C: VERSION<TAB>doveadm-server<TAB>1<TAB>0

All the fields are TAB-separated. The server will send you back either:

  • + means you are preauthenticated and can start sending commands. This happens when connecting to the UNIX socket.

  • - means you need to authenticate first.

TIP

As of Dovecot v2.2.34, Dovecot sends the "+" or "-" only after VERSION, while earlier versions sent it already before VERSION. This shouldn't change much practically, because the client was supposed to have sent the VERSION immediately anyway.

Authentication ​

The authentication is done with a regular SASL PLAIN authentication, i.e. PLAIN<tab>base64(\0username\0password). Currently the username must be doveadm. For example for user=doveadm, password=secret use:

C: PLAIN<TAB>AGRvdmVhZG0Ac2VjcmV0
S: +

Running Commands ​

The actual commands are in format: flags<tab>username<tab>command name[<tab>parameter[<tab>parameter2...]], where the flags can be either empty, "v" (verbose) or "D" (debug). Note that if the command name has spaces, they are sent as spaces instead of as tabs (e.g. "quota get", not quota<tab>get). So for example to get a quota for user tss:

C: <TAB>tss<TAB>quota<TAB>get
S: user STORAGE 1814    -       0       user    MESSAGE 6       -       0
S: +

The storage values are all given in kilobytes.

The server replies using the same fields TAB-separated as what a regular doveadm command sends. The reply itself ends with LF. So if the reply is large, it may return a very long line as a reply. After the reply follows a status line:

  • + = success.

    • In future the + may be followed by more text, for now you should just ignore those.

  • - = failed. The error was probably logged to Dovecot's error log. The - may be directly followed by an error code:

    • NOUSER: The user doesn't exist.
    • TEMPFAIL: Temporary failure.
    • NOPERM: Permission denied.
    • PROTOCOL: Protocol-related error.
    • DATAERR: Input data (e.g. command parameters) were wrong.
    • NOTFOUND: The command didn't find the requested object.

Available Commands ​

The command names and output are exactly the same as what regular doveadm commands on command line do. Earlier Dovecot versions supported running only "mail commands" (commands with -u username parameter), but v2.3 should support all commands.

You can use the doveadm itself to find out what the output format will look like. For example:

sh
doveadm -f tab search mailbox inbox 1:2
mailbox-guid    uid
fa8cb722dfad9c52b62600007049b30b        125159
fa8cb722dfad9c52b62600007049b30b        125160

There are two fields, "mailbox-guid" and "uid" in the output. The title names won't be sent via doveadm protocol, but everything else will be sent in one line. So in the above case the protocol output will be:

fa8cb722dfad9c52b62600007049b30b<tab>125159<tab>fa8cb722dfad9c52b62600007049b30b<tab>125160

Multiplex Stream ​

Multiplex streaming is enabled if client sends protocol minor version 1 or higher:

C: VERSION<TAB>doveadm-server<TAB>1<TAB>1

After authentication has successfully finished (server returned +), the client must switch reading and writing to the "multiplex mode". This protocol works by sending packets:

  • 1 byte: Channel ID
  • 4 bytes: Following data length in big-endian
  • Data

The channel ID is:

  • 0: doveadm protocol
  • 76 ('L'): Logs sent by doveadm-server

STARTTLS ​

If doveadm-server returns minor version 2 or higher, it supports the STARTTLS command. This command can be sent only if the server hasn't already pre-authenticated the client, because it's running on a trusted UNIX socket. So when the doveadm-server returns the - line indicating authentication is needed, the doveadm-client can send STARTTLS line. After this both the client and server switch to TLS. There is no response to this command.

Example Clients ​

Perl: Net::Doveadm

Copyright © Open-Xchange GmbH