Maildir Configuration

See Maildir for a technical description of how Dovecot has implemented Maildir support.

Mail Location

Maildir exists almost always in ~/Maildir directory. The mail location is specified with:

mail_location = maildir:~/Maildir

Directory Layout

By default, Dovecot uses Maildir++ directory layout. This means that all mailboxes are stored in a single directory and prefixed with a dot. For example:

  • Maildir/.folder/

  • Maildir/.folder.subfolder/

If you want Maildirs to use hierarchical directories, such as:

  • Maildir/folder/

  • Maildir/folder/subfolder/

you’ll need to enable fs layout:

mail_location = maildir:~/Maildir:LAYOUT=fs

Control Files

Dovecot stores some Maildir metadata into two control files:

  • dovecot-uidlist file contains IMAP UID <-> Maildir filename mapping

  • dovecot-keywords file contains Maildir filename flag (a..z = 0..25) <-> keyword name mapping

Both of these files are described fully in :ref:maildir_mbox_formats. The important thing to remember about them is that they shouldn’t be treated the same way as index files. Index files can be deleted and rebuilt without any side effects, but if you delete control files you’ll cause messages to get new UIDs and possibly lose keyword names.

If the messages get new UIDs, the IMAP clients will invalidate their local cache and download the messages all over again. If you do this for all the users, you could cause huge disk I/O bursts to your server.

Dovecot cannot currently handle not being able to write the control files, so it will cause problems with filesystem quota. To avoid problems with this, you should place control files into a partition where quota isn’t checked. You can specify this by adding :CONTROL=<path> to mail_location:

mail_location = maildir:~/Maildir:CONTROL=/var/no-quota/%u

Index Files

See Index files for a full explanation of how to change the index path. Example:

mail_location = maildir:~/Maildir:INDEX=/var/indexes/%u


  • ref:maildir_copy_with_hardlinks = yes <setting-maildir_copy_with_hardlinks>

  • ref:maildir_stat_dirs = no <setting-maildir_stat_dirs>

  • ref:maildir_very_dirty_syncs = yes <setting-maildir_very_dirty_syncs>

Filesystem Optimizations

See Maildir and Filesystems.

Mailbox Directory Name

When using LAYOUT=fs, there is a potential for naming collisions between Maildir’s new/, cur/, and tmp/ subdirectories, and mail folders of the same names.

For example, consider a mail folder foo/bar. Under LAYOUT=fs, data for this mail folder will be stored under Maildir’s usual three directories ~/Maildir/foo/bar/{new,cur,tmp}/. If the user then tries to create a mail folder foo/bar/new, this would then imply that data should be stored in Maildir’s three directories ~/Maildir/foo/bar/new/{new,cur,tmp}/. But this would overlap Maildir’s new/ subdirectory of mail folder foo/bar.

This may not be a problem in many installations, but if a risk of collisions with Maildir’s three subdirectory names is perceived, then the DIRNAME parameter can be used. For example, if we specify mail location as:

mail_location = maildir:~/Maildir:LAYOUT=fs:DIRNAME=mAildir

then this will push Maildir’s new/, cur/, and tmp/ subdirectories down into a subdirectory mAildir/, so a mail folder foo/bar would be stored at ~/Maildir/foo/bar/mAildir/{new,cur,tmp}/. A mail folder foo/bar/new would be stored at ~/Maildir/foo/bar/new/mAildir/{new,cur,tmp}/, which would then have no overlap with the mail folder foo/bar.

DIRNAME affects INBOX slightly differently. Without DIRNAME, INBOX will be stored at ~/Maildir/{new,cur,tmp}/, but when DIRNAME is specified, we get an extra path component INBOX/ immediately prior to the DIRNAME value, so in the example above INBOX would be stored at ~/Maildir/INBOX/mAildir/{new,cur,tmp}/.

The value for DIRNAME should be chosen carefully so as to minimise the chances of clashing with mail folder names. In the example here, unusual upper/lower casing has been used.



If enabled, do not obtain a mail message’s physical size from the S=<size> data in the Maildir filename except when recalculating the Maildir++ quota.


Should mail messages always be moved from the new/ directory to cur/, even when the \Recent flags aren’t being reset?


If enabled, don’t include directories in a LIST response that begin with a dot. Thus, if disabled, Dovecot assumes that all the files beginning with a dot in the Maildir are Maildirs.

You shouldn’t have any non-directory files beginning with a dot in the Maildirs, but if you do you may need to set this to yes, in which case Dovecot needs to stat() each directory entry, which degrades the performance. Some filesystems provide the directory/non-directory status for free without having to stat(). In those filesystems this setting is ignored.


If enabled (yes), Dovecot is assumed to be the only MUA that accesses Maildir directly, so the cur/ directory is scanned only when its mtime changes unexpectedly or when the mail cannot otherwise be found.

If enabled and another process (or a Dovecot process which doesn’t update index files) does changes to cur/ while the mailbox is simultaneously being modified by Dovecot, Dovecot may not notice those external changes. It is still safe to deliver new mails to new/ using non-Dovecot software (except with mailbox_list_index = yes, changes aren’t noticed outside INBOX).